Produse pentru 2 ingredient epoxid (5)

Syntech Poliurea Primer – Epoxy Metal Syntech Poliurea Primer – Epoxy Metal is a two-component primer based on epoxy resins free from solvents, used to promote adhesion, as a surface sealant for concrete, applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. Adhesion promoter, surface sealant for concrete, to be applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. The application must take place on a dry and degreased surface; the substrate must not have crumbly or detached parts and with a degree of humidity that must not exceed 5%. Preparation of the substrate may require some types of mechanical action: Smoothing, bush-hammering, shot peening, hydro-washing. Other mechanical actions that can make the support suitable. The individual components must be mixed carefully until a homogeneous mass is obtained. The material can be applied by roller, brush or spray by means of special airless machines, even in two coats. The temperature of the support must always be at least 3°C higher than the dew point temperature. Minimum application temperature +5°C, maximum temperature +35°C. Approximately 0,20 kg of Syntech Poliurea Primer – Epoxy Metal for every square metre of surface to be treated. Can 10 kg [A] - Can 5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B]

Mister Dry Tornado T2 è un nuovo straordinario prodotto ecologico che permette di rimuovere adesivo epossidico dalle superfici come pavimentiue rivestimenti senza dover utilizzare altri prodotti chimici senza alterare o rovinare gli stessi. Un altro prodotto della gamma per la eco pulizia della Emme di Service, e sempre e rigorosamente made in italy

One Side Adhesive for LEATHER'S PRODUCERS The NEOPRENE ONE WAY is a plychloroprene adhesive adapt for LEATHER'S PRODUCERS and GIUNETRIA in particular in the case where you want apply the glue only in a side. Used for the construction of insoles in shoes too. It has high viscosity. High bond strength. CHARACTERISTICS : Viscosity : 2800 +/- 100 cPs Opened Time : 30 - 60 Minutes USING INSTRUCTIONS : Apply an homogeneous coat upon one of the two parts has to be sticked, let it dries for at least 10 - 15 minutes and join the two parts with hands, hammer or with a press. To dilute the PRODUCT, use SOLVENT P or SOLVENT M. The products has to be conserved in the original tins well closed and in a cool and dry place. N.B.: All the indications over reported are without obligation and warranty. PACKAGING : Kg 800 - Kg 200 - Kg 40 - Kg 15 - Kg 9 Kg 4 - Kg 1 .

EG 91 Epoxy-polyurethane two-component elastoplastic and thixotropic sealant, for joints subject to traffic, where Shore A Hardness Scale = 65. The elongation-at-break is 70%. To be applied with a trowel or extruded into the suitably-taped sections of the joint (to protect adjacent surfaces). Resistant to contact with hydrocarbons (gasoline and diesel fuel). Horizontal sealing of joints in industrial flooring, even in the presence of chemical attacks and stresses from average-heavy traffic. Vertical sealing of joints in concrete works and products. The application and containment surfaces (joint walls) should be clean, dry, conveniently prepared and adequately resistant: free from dust, grease, soiling, crumbling and/or non-adhering parts and dry. The application surfaces must also be preliminarily treated with Protech Flex Primer. Add component B to component A taking care to pick up all the material contained in the packs, mix thoroughly with a mixer at a low number of revolutions, until a perfectly homogeneous mix is obtained; add the required load amount (component C) continue to mix until a perfectly homogeneous mixture is obtained, indicated by the uniform colour of the mixture. Apply the product mixed by trowelling or with extrusion guns. Do not apply with temperatures below + 5°C or higher than + 35°C and in the presence of surface stagnant water. Approximately 1.25 kg of EG 91 per cubic decimetre of joint volume to be sealed (1250 kg per cubic metre). Packaging: Kit of 5+2.5 kg UM: €/kg

Leather Sole Adhesive The NEOPRENE 1 is a plychloroprene adhesive with high crystallization used for cold sticking of LEATHER SOLES, for the assembly of the GUARDOLO and for the to pair LEATHER-LEATHER and LEATHER-TUNITH. High bond strenght. CHARACTERISTICS : Viscosity : 2800 +/- 100 cPs Opened Time : 15 - 30 Minutes USING INSTRUCTIONS : Apply an homogeneous coat upon the two parts has to be stickked, let them dry for at least 10 - 15 minutes and join the two parts with hands, hammer or with a press. To dilute the PRODUCT, use SOLVENT P or SOLVENT M. The products has to be conserved in the original tins well closed and in a cool and dry place. N.B.: All the indications over reported are without obligation and warranty. PACKAGINGS : Kg 800 - Kg 200 - Kg 40 - Kg 15 - Kg 9 Kg 4 - Kg 1